CoA. Reports

Permanent URI for this collection

Browse

Recent Submissions

Now showing 1 - 20 of 280
  • ItemOpen Access
    Addendum to type record. Avro "Lancaster" Mk.1 P. A. 474 Type record No. 1/P1/Lancaster. Investigation of boundary layer conditions on wings. M.O.S. Contract No.6/Aircraft/9807/C. B. 6(a)
    (College of Aeronautics, 1956-01) College of Aeronautics, Department of Aircraft Design
    Introduction The investigation involves, briefly, the mounting of a wing of 45' sweep-back in a dorsal position on the fuselage of 'Lancaster' P.A.474 such that wing incidence will be variable in flight over a 20 range, i.e. ± 100. A ‘partial chord’ technique for swept wings has been established by the College using a similar wing mounting configuration on an Avro 'Anson' Aircraft and this technique has been applied to the current investigation.
  • ItemOpen Access
    The elastic stability of sandwich plates
    (College of Aeronautics, 1949-03) Hunter-Tod, J. H.
    This paper treats the elastic stability of supported rectangular plates of sandwich construction with isotropic and aeolotropic fillings under compression and shear loading. Formulae are developed for critical stresses for flat and curved panels in compression and flat panels in shear for the buckling of the whole panel, also for the wrinkling or local failure of the faces of flat panels in compression. A method is indicated for calculating the critical load of a cylinder in pure bending. It is established that for a wide range of conditions the critical stress for panels buckling in compression is independent of the form of the filling providing it is symmetrical about the normal; of the elastic constants of the filling only the transverse shear is of concern. As a result a simple extension of the equivalent plate theory of greatly improved accuracy is developed enabling the use of equations treating the plate as a whole.
  • ItemOpen Access
    Measurement of the derivative 'ZW' for an oscillating aerofoil
    (College of Aeronautics, 1950-06) Buchan, A. L.; Harris, K. D.
    This report presents the results of experimental measurements of the damping derivative coefficient zw for constant chord rigid wings of various aspect ratios having sweepback angles of zero and 450. The results for the rectangular wings Flow substantial agreement with the unsteady aerofoil theory developed by TI.P. Jones $2) The dependence of Zvi upon frequency parameter is as given by theory and is much less than for two dimensional flow, but the numerical results are approximately 10 per cent below the theoretical. This is attributed to the large trailing edge angle 22° of the N.A.C.A. 0020 section used for the model aerofoils. The effect of sweepback is to decrease the numerical value of z , but this effect is much less pronounced, for low than for high aspect ratios. For aspect ratios 5 and 3 the numerical value is greater than would be given by a factor of proportionality equal to the cosine of the angle of sweepback. The measurements were corrected for tunnel interference by a method based on the theoretical work of 7.P.Jones.(1)
  • ItemOpen Access
    Laplace plane GeoSAR feasibility study: summary of the group design project MSc in astronautics and space engineering 2014-15, Cranfield University
    (Cranfield University, 2015-10-07) Hobbs, Stephen
    Students of the MSc course in Astronautics and Space Engineering 2014-15 at Cranfield University performed a feasibility study of a geosynchronous radar mission for their group project. This report summarises the students' work and their findings. The report consists of an overview and discussion of the technical work of the project and a compilation of the executive summaries which describe the special contributions of each student. The mission studied is a geosynchronous synthetic aperture radar Earth observation mission using the Laplace orbit plane to reduce station-keeping propulsion demand. User applications are drawn from a wide range of sectors (agriculture, meteorology, geohazards, etc.) and are translated into system design requirements. The proposed mission design uses satellites with 13 m diameter antennas and a total electrical power demand of 6 kW. The mission seems feasible, although further study is recommended especially for the areas of _ orbit selection with respect to user requirements, imaging performance and orbit maintenance, _ mass budget (driven largely by the propulsion system), _ user requirements, imaging performance and operational imaging modes, _ opportunities for improved imaging with a constellation.
  • ItemOpen Access
    Generic regional aircraft flying qualities for the approach and landing task
    (Cranfield University, 1997-08) Gautrey, Jim
    Many changes have occurred in the past 20 years in aircraft manufacture and development. New technologies have appeared, spanning the entire aircraft design environment, such as new production methods, new materials and new avionics systems. These new methods have been developed for two reasons. For military aircraft, they have arisen through the need to improve performance. However, for civil aircraft they have arisen through the need to reduce the overall cost. This report considers one aspect of these technologies for civil aircraft: fly-by-wire. This technology uses electrical signalling in place of conventional heavy mechanical control runs. In addition, flyby- wire generally permits improvements to be made in aircraft flying and handling qualities. This requirement has originated from two main sources; a need to make improvements in the light of an increasing amount of experience, and a requirement to cope with aerodynamic modifications which have been implemented to improve aerodynamic efficiency, but which have a deleterious effect on the aircraft's flying and handling qualities. Both of these adverse effects have come about from a desire to reduce costs for the end aircraft user, i.e. the airlines. The aircraft used for these evaluations is a Generic Regional Aircraft, of about 100 seats and a weight of 90,000 lbs. Only a limited portion of the flight envelope was considered since these evaluations primarily concentrate on the approach and landing flight phase. These evaluations are being carried out as part of a joint Avro International Aerospace — Cranfield University Engineering Doctorate programme researching advanced flight control system design for a Generic Regional Aircraft. The overall aim of this programme is to produce a control law design which gives aircraft in question excellent handling qualities. The evaluations described here comprise the first in a series of three planned studies, and consider solely the approach and landing flight phase.
  • ItemOpen Access
    On a theory of sandwich construction
    (College of Aeronautics, 1948-03) Hemp, W. S.
    The theory of sandwich construction developed in this paper proceeds from the simple assumption that the filling has only transverse direct and shear stiffnesses, corresponding to its functional requirements (§1). This supposition permits integration of the equilibrium equations for the filling (§2). The resulting integrals are used to study the compression buckling of a flat sandwich plate (§3). The formulae obtained are complex, but may be simplified in practical cases (§4). A second approach to sandwich problems is made in §5, where a theory of "bending" of plates is outlined. This generalises the usual theory, making allowance for flexibility in sheer. This approach is applied to overall compression buckling of a plate in §6, and agreement with the previous calculations is found. This suggests the possibility of calculating buckling loads for curved sandwich shells. A simple example, the symmetrical buckling of a circular cylinder in compression is worked out in §7. The theory developed would seem applicable to all cases of buckling of not too short a wave length (§8).
  • ItemOpen Access
    Note on the limits to the local Mach number on an aerofoil in subsonic flow
    (College of Aeronautics, 1948-10) Young, A. D.
  • ItemOpen Access
    Note on the limits to the local Mach number on an aerofoil in subsonic flow
    (College of Aeronautics, 1948-04) Young, A. D.
    It has been noted in some experiments that the local Mach number just ahead of a shock wave on an aerofoil in subsonic flow is limited, values of the limit of the order of 1.4 are usually quoted. This note presents two lines of thought indicating how such a limit may arise. The first starts with the observation that the pressure after the shock will not be higher than the rain stream pressure. Fig.1 shows the calculated relation between local Mach number ahead of the shock (M„ 1 ), shock inclination (S), mainstream Mach number (M1) and pressure coefficient just aft of the shock. • (Cp) It is noted that, for given M1 , Cp and .5 ,two shocks are possible in general, a strong one for which Ms , > 1.48, and a weak one for which MS1 < 1.48, and it is argued that the latter is the more likely. The second approach is based on the fact that a relation between stream deflection (8) and Mach number for the flow in the limited supersonics regions on a number of aerofoils has been derived from some. experimental data. Further analysis of experimental data is required before this relation can be accepted as general. If it is accepted, however, then it indicates that the Mach numbers increase above unity for a given deflection is about one-third of that given by simple wave theory (Fig.2). An analysis of the possible deflections on aerofoils of various thicknesses (Fig.3) then indicates that deflections corresponding to local Mach numbers of the order of 1,5 or higher are unlikely except at incidences of the order of5 ° or more, and may then be more likely for thick wings than for thin wings. Flow breakaway will make the attainment of such high local Mach numbers less likely.
  • ItemOpen Access
    Temperature effects on material characteristics
    (College of Aeronautics, 1960-08) Murphy, A. J.; Kennedy, A. J.
    Some of the physical properties of the main elements of interest in high temperature technology are reviewed. Some general trends emerge when these properties are viewed as a function of melting point, but there are a few notable exceptions. Titanium, zirconium, niobium and tantalum all have disappointingly low moduli; chromium is excellent in many ways, but has a limited ductility at lower temperatures; molybdenum oxidises catastrophically above about 700° C, and niobium suffers from severe oxygen embrittlement. Beryllium and carbon (in the graphitic form) both stand out as exceptional materials, both have very low densities, beryllium a very high modulus but an unfortunately low ductility, while graphite has a relatively low strength at the lower temperatures, although at temperatures of 2000° C and above it emerges as a quite exceptional (and probably as the ultimate) high temperature material. Some of the fundamental factors involved in high temperature material development are examined, in the light, particularly, of past progress with the nickel alloys. If a similar progress can be achieved with other base elements then a considerable margin still remains to be exploited. Protection from oxidation at high temperatures is evidently a factor of major concern, not only with metals, but with graphite also. Successful coatings are therefore of high importance and the questions they raise, such as bonding, differential thermal expansion, and so on, represent aspects of an even wider class covered by the term “composite structures". Such structures appear to offer the only serious solution to many high temperature requirements, and their design, construction and utilization has created a whole series of new exercises in materials assessment. Matters have become so complex, that a very radical and fundamental reassessment is required if we are to change, in any very significant way, the wasteful and ad hoc methods which characterise so much of present-day materials engineering.
  • ItemOpen Access
    Boundary layers with suction and injection a review of published work on skin friction
    (College of Aeronautics, 1960-09) Craven, A. H.
    Available data on the effects of suction and injection on skin friction are summarised and compared. It is shown that injection into a turbulent boundary layer can produce a skin friction coefficient lower than the laminar value at trio same Reynolds number on an impermeable plate.
  • ItemOpen Access
    Skin friction in the laminar boundary layer in compressible flow
    (College of Aeronautics, 1948) Young, A. D.
  • ItemOpen Access
    Multi-objective Tabu Search 2: first technical report
    (Cranfield University, 2015-06) Tsotskas, Christos; Kipouros, Timoleon; Savill, Mark A.
    The purpose of this document is to describe Multi-Objective Tabu Search 2 (MOTS2), which is a native mutli-objective optimiser. It has been developed to tackle a variety of real-world problems of engineering interest. The design and implementation are presented, followed by verification, validation and user instructions. At a glance, it involves introduction to the algorithm, explains configuration settings and structure, and results interpretation. Then, the optimiser is tested against a series of mathematical test functions in order to verify its functionality. The main goal is to demonstrate and assess the performance and applicability of the optimiser. The next step is to use MOTS2 on a real-world case, where the performance of optimising a 2D airfoil is validated and illustrated.
  • ItemOpen Access
    Ignoration of distortional co-ordinates in the theory of stability and control
    (College of Aeronautics, 1946-12) Duncan, W. J.
    Gates and Lyon have proposed to treat theoretically the stability and control of deformable aircraft by a method in which the distortion co-ordinates are ignored and the influence of distortion is allowed for by suitable modifications of the derivatives and other coefficients. in the 'present paper an exact method for eliminating the distortion co-ordinates is given and the conditions in which the true eliminant conforms with the simplification of Gates and Lyon are examined. In general the simplification is not justified mathematically, but in certain circumstances it provides an acceptable approximation. it will not be practically valid unless the structural distortions occur so relatively slowly that the associated inertia forces are negligible, i.e. the distortions must be quasi-static.
  • ItemOpen Access
    A theoretical and experimental investigation of tail unit flutter on the M.S. 760 'Paris'
    (College of Aeronautics, 1962) Mitchell, C. G. B.; Johns, D. J.
    After an incident which, it was suspected, was due to symmetric elevator flutter, had occurred on the Morane-Saulnier 760 operated by the College of Aeronautics, Cranfield, a theoretical and experimental investigation of the aircraft's flutter characteristics was undertaken. The theoretical investigation consisted of binary and ternary symmetric flutter calculations with and without the control circuit included. These showed the aircraft to be liable to flutter for mass distributions similar to that which existed at the time of the incident. The experimental work consisted of flight flutter tests using control jerk excitation with both film and magnetic tape recording. These showed that the aircraft as supplied by the makers had a critical speed for symmetric elevator flutter of 380 knots, but that this could be lowered to 240 knots by the installation of a stick force indicator combined with unfavourable distributions of fuel load and fuselage mass distribution. The tests also showed the tail unit mode excited by rudder kicks to be safe, but as doubt exists as to whether this mode is the most critical antisymmetric one, further work is needed on this aspect. A 75 c. p. s. rudder buzz was encountered that was not caused by compressibility effects. As a result of this investigation the elevator mass balance was increased and the aircraft proved to be free from elevator flutter up to at least 400 knots. A general conclusion reached in this investigation was that static balancing of control surfaces should include the effect of components of the control circuit attached to them if those components contribute to the inertia couplings induced by vibration in other elastic modes.
  • ItemOpen Access
    Experimental investigation on a cropped delta wing with edge blowing
    (College of Aeronautics, 1963-06) Alexander, A. J.
    Low speed wind tunnel tests have been made on a 70° cropped delta wing with edge blowing both in the plane of the wing and at a downward deflection angle of 30°. The tests include six-component force and moment measurements, the distribution of static pressure at four chordwise stations, and quantitative measurements of the flow in the leading edge vortex. At a constant incidence, blowing increases the size and strength of the leading edge vortices and moves the vortex cores outwards and upwards. Blowing also tends to suppress the secondary separation due to the entrainment effect of the jet. Blowing from the streamwise tips and trailing edge was relatively ineffective and most of the tests were made with blowing from the swept leading edges only, with tips and trailing edge sealed.
  • ItemOpen Access
    Experiments on a delta wing using leading edge blowing to remove the secondary separation
    (College of Aeronautics, 1963-05) Alexander, A. J.
    It is found that the entrainment effect of a thin jet emerging from the leading edge of a delta wing is sufficient to remove the secondary separation. The minimum jet momentum required is small, but increases with incidence. Tests made without blowing, and with minimal blowing, include balance measurements, pressure plotting and tuft studies, over the range of incidence α = 0[degrees] - 20[degrees] . It is concluded that the presence of the secondary separation does not affect the lift or the vortex height appreciably, but is at least partly responsible for the large discrepancy between theory and experiment with regard to the spanwise position of the vortex.
  • ItemOpen Access
    Slip flow past slender pointed bodies
    (College of Aeronautics, 1963-05) Stribling, C. B.
    Using Oseen's approximation to linearise the Navier-Stokes equations, a solution to the problem of axisymmetric slip flow past slender bodies of revolution at zero incidence has been obtained, in a manner similar to that used by Laurmann in his paper on the slip flow past a flat plate(6). The drag coefficient has been evaluated for both incompressible and compressible flows, and this has been compared with normal boundary layer values. It is found that the skin friction drag is the dominant component of drag in the incompressible case and in the compressible case.
  • ItemOpen Access
    The free-molecule flow of a polyatomic gas
    (College of Aeronautics, 1963-05) Marsh, T.
    A study has been made of the free-molecule flow of a polyatomic gas past a body, with special reference to the evaluation of accommodation coefficients. A model of the gas-surface interaction is devised, based on the phenomenon of physical adsorption. Using this model, expressions for the thermal accommodation coefficients of the various energy modes of a polyatomic gas are developed by postulating that the energy exchange at the surface is governed by equations similar in form to the gas-phase relaxation equations. The expressions so obtained are dependent on the relevant integral heat of adsorption and the various relaxation times involved. Some suggestions are put forward as to how these relaxation times could be evaluated since, once their behaviour is known, the results of this report will provide a simple method for estimating the accommodation coefficients in a wide range of flow conditions.
  • ItemOpen Access
    Statistical parameters in planning aero-engine production
    (College of Aeronautics, 1963-02) Atkinson, A. H.; Harris, J. T.
    This report considers the estimation of statistical parameters and their application to production planning in the aero-engine industry. A similar pattern of behaviour to that already recognised as existing in the airframe industry is found to operate, though there are indications of quantitative differences. The build-up time to the planned peak rate of production in a particular situation is found to be about eighteen months but with variation between firms. The reduction in operator performance time, which occurs with repetition during the build-up period and afterwards, is discovered to be present in machining as well as assembly, but to a lesser extent. The logarithmic function generally descriptive of such a tendency is found to fit the actual man-hour content values rather than the cumulative average ones. The relationship between the logistic of output and the logarithmic function is established and made use of to estimate labour requirements from the commencement of production onwards. In addition to the above consideration of production variables, examples are given of the use of engine performance ratings to estimate costs. Finally, because of the importance of planning to productivity, a typical production programme has been included.
  • ItemOpen Access
    On the application of boundary layer control to a slender wing supersonic airliner cruising at M = 2.2
    (College of Aeronautics, 1962-04) Craven, A. H.; Hopkins, H. L.
    The use of suction or injection to reduce the drag of a supersonic airliner is considered. It is shown that injection gives no reduction in operating costs. With suction applied to an M =2.2 aircraft on the London - New York route, the basic operating cost of 13.30d per short ton statute mile is expected to be reduced by 0.5d for the same payload assuming no change in configuration. If the theoretical maximum skin friction reduction could be obtained the payload could be increased by 4750 lb. and the direct operating cost could be reduced to 10.63d per short ton statute mile.