CERES Home
→
School of Engineering (SoE)
→
CoA. Notes: Production and Industrial Administration (1963-1969)
→
Browsing CoA. Notes: Production and Industrial Administration (1963-1969) by Publication Date

Browsing CoA. Notes: Production and Industrial Administration (1963-1969) by Publication Date

Now showing items 1-18 of 18

Fluid logic devices: a review

Charnley, C. J. (College of Aeronautics, 1963-09)

Background study of work connected with this report entailed the collection of a large number of specialised and general technical publications concerning the techniques and applications of fluid computing. General ...
Diffraction gratings - their principles and applications to machine tools

Healey, M. (College of Aeronautics, 1963-12)

The use of diffraction gratings as measuring elements on machine tools is nowadays an accepted procedure. Part I of this paper therefore sets out to give a brief understanding of the principles of diffraction gratings, ...
Investigation into the possibility of applying lubrication theory to the selection of optimum clearance fits for plain hydrodynamically lubricated bearings

Loxham, J. (College of Aeronautics, 1964-02)

BS1916 limits and fits for engineering is based on ISA bulletin 25 which was first issued in 1921 and designed for use with the metric system. It provides a wide range of tolerances for holes and shafts from which it is ...
Calculating the shear angle in orthogonal metal cutting from fundamental stress-strain-strain rate properties of the work material

Oxley, P. L. B.; Welsh, M. J. M. (College of Aeronautics, 1964-03)

An analysis of the orthogonal metal cutting process is made which enables the shear angle to be calculated from certain fundamental properties of the work material and the specified cutting conditions. Shear angles are ...
Human factors specification for a machine tool scale reader

Easterby, R. S. (College of Aeronautics, 1964-05)

The length measuring devices on many machine tools must usually cover a large range while maintaining high accuracy for small incremental movements. Many machines use the operator as part of the measuring system, where ...
Position transducers for numerically controlled machine tools

Charnley, C. J. (College of Aeronautics, 1964-12)

The paper covers the basic text book theory of all forms of position transducer used on commercial numerically controlled machine tools. Some attempt is made to categorise and indicate the scope and usage of these devices. ...
Electro-chemical machining

Glew, D. A. (College of Aeronautics, 1965-02)

This report introduces the reader to the process and to the requirements which must be considered for its installation on the shop floor. Although only electro-chemical shaping is dealt with, many of the parameters ...
An evaluation of the British standard proposals for symbols on machine tool indicator plates

Easterby, R. S. (College of Aeronautics, 1965-03)

The work detailed in this report has been undertaken as part of a research project supported by the Machine Tool Industry Research Association on Ergonomics and Machine Tool Design. In an early research project report, some ...
Business in Europe: three studies of European business and the prospects for British companies exporting to or establishing subsidiaries in Europe

Cranfield Management Development Programme, (MDPii) (College of Aeronautics, 1965-07)

The Cranfield Management Development Programme is an intensive ten week course for middle management aged 23 - 38. The courses which are held twice yearly started in 1964; the second of these MDP II was held from April ...
Studies of two aspects of business in Europe

Cranfield Management Development Programme no. 3. (College of Aeronautics, 1965-12)

The Cranfield Management Development Programme is an intensive ten week course for middle management aged 28 - 38. The courses which are held twice yearly started in 1964; the third of these MDP III was held from October ...
Studies of four aspects of business in Europe

Cranfield Management Development Programme No. 4. (College of Aeronautics, 1966-07)

Preface The Cranfield Management Development Programme is an intensive ten week course for middle management aged 28 - 38. The courses which are held twice yearly started in 1964; the fourth of these, MDP 4, was held ...
Thrust and stiffness nomograms for hydrostatic bearing calculations

Cooke, P.; Scarr, A. J. (College of Aeronautics, 1966-08)

The application of hydrostatic lubrication to slideways is now becoming common practice in the machine tool industry. The theoretical basis for determining design parameters for hydrostatic lubrication is well established ...
Dimensional changes resulting from the heat treatment of EN 30B and Nimar 125

Noble, C. F. (College of Aeronautics, 1966-12)

Three components have been manufactured in both EN 30B and N1MAR 125. Dimensional changes following heat treatment have been recorded and, while the sample is only small, the report serves to illustrate the potential benefits ...
Studies of four aspects of business in Europe

Cranfield Management Development Programme No. 5. (College of Aeronautics, 1967-03)

Preface The Cranfield Management Development Programme is an intensive ten week course for middle management aged 28 - 38. The courses which are held twice yearly started in 1964; the fifth of these, MDP 5, was held ...
Studies of selected aspects of business in Europe

Cranfield Management Development Programme no. 7. (College of Aeronautics, 1968-01)

Preface The Cranfield Management Development Programme is an intensive ten week course for middle management aged 28 - 45. The courses which are held twice yearly started in 1964; the seventh of these, M.D.P.7, was held ...
Sampling techniques and their application to managerial problems

Wiltshire, H. C. (College of Aeronautics, 1968-10)

In future managers will depend more on numerical information in making decisions, and this information will be more readily available with the extension of the use of computers. Some of the decisions made by management ...
Incremental control

Watson, A. L.; McQue, D. W. (College of Aeronautics, 1969-06)

This Note describes the control of a centre lathe using stepping motors and a small computer. The mechanical conversion is low cost and the system described is readily adaptable to the simultaneous control of a group ...
The improvement of micro-electronic component production operations by the application of cranfield developed precision engineering techniques

McRobb, R. M. (College of Aeronautics, 1969-10)

From an examination of the Cranfield Universal Measuring Machine certain features were selected. These features were linked together with some of the manufacturing and assembly operations used to make dual-in-line ...

Browsing CoA. Notes: Production and Industrial Administration (1963-1969) by Publication Date

Browsing CoA. Notes: Production and Industrial Administration (1963-1969) by Publication Date

Search CERES

Browse

All of CERES

This Collection

My Account