Browsing by Author "Han, Jian"

Now showing 1 - 4 of 4
  • Thumbnail Image
    ItemOpen Access
    HAZ effects in hot-rolled dual-phase steel during flash butt welding of wheel rims
    (Springer, 2023-09-29) Han, Jian; Zhu, Lisong; Wang, Jun; Zhang, Caidong; Sun, Li; Zhang, Zhigiang; Ma, Cheng; Jiang, Zhengyi; Linton, Valerie
    The embrittlement and softening behavior in simulated heat-affected zones (HAZ) of a newly designed dual-phase DP680 steel for wheel rim applications with different flash allowances were investigated to determine weldability, and offer valuable information for the steel design and its subsequent flash butt welding (FBW). The characterization of microstructure and mechanical performance for the simulated HAZ was conducted by means of optical microscopy, scanning electron microscopy, electron backscatter diffraction, hardness distribution, and Charpy V-notch (CVN) values at selected temperatures. The investigation demonstrates that the toughness of coarse-grained HAZ was kept at an average level of 25.3 J when the prior austenite grain size was controlled to 60.54 μm at a flash allowance of 14 mm (equivalent to heat input of 15.14 kJ/cm based on real welding process), which exhibits the worst toughness when the flash allowance was changed from 4 to 14 mm. Further, with a higher martensite fraction (> 30 pct) in base material (BM), the softening occurs in inter-critical HAZ (ICHAZ) instead of sub-critical HAZ since most of martensite in ICHAZ has decomposed, and the rest ferrite and newly formed bainite with remaining martensite reduce the hardness to a larger extent compared to SCHAZ, whose martensite has only partly decomposed. Even if the softening degree is up to 21.6 pct compared to the BM (average 233 HV0.5), the work hardening during a series of forming processes after FBW has alleviated the softening evidently (work hardening degree > 10 pct). However, the failure location is still in ICHAZ after forming extension which has been confirmed in practical applications of DP680 FBW and subsequent forming processes.
  • Thumbnail Image
    ItemOpen Access
    Optimising two-stage vacuum heat treatment for a high-strength micro-alloyed steel in railway spring clip application: impact on microstructure and mechanical performance
    (MDPI, 2023-07-10) Lu, Yao; Wang, Jun; Pan, Di; Han, Jian; Zhu, Lisong; Diao, Chenglei; Han, Jingtao; Jiang, Zhengyi
    The heat treatment process is a vital step for manufacturing high-speed railway spring fasteners. In this study, orthogonal experiments were carried out to obtain reliable optimised heat treatment parameters through a streamlined number of experiments. Results revealed that a better comprehensive mechanical performance could be obtained under the following combination of heat treatment parameters: quenching temperature of 850 °C, holding time of 35 min, medium of 12% polyalkylene glycol (PAG) aqueous solution, tempering temperature of 460 °C, and holding time of 60 min. As one of the most important testing criteria, fatigue performance would be improved with increasing strength. Additionally, a high ratio of martensite to ferrite is proven to improve the fatigue limit more significantly. After this heat treatment process, the metallographic microstructure and mechanical properties satisfy the technical requirements for the high-speed railway practical operation. These findings provide a valuable reference for the practical forming process of spring fasteners.
  • Thumbnail Image
    ItemOpen Access
    Physical simulation and numerical simulation of flash butt welding for innovative dual phase steel DP590: a comparative study
    (MDPI, 2023-05-03) Song, Jingwen; Zhu, Lisong; Wang, Jun; Lu, Yao; Ma, Cheng; Han, Jian; Jiang, Zhengyi
    In this study, the microstructure and performance of newly designed dual-phase steel (DP590) after joining by flash butt welding (FBW) for vehicle wheel rims was analysed and compared by two simulations, i.e., physical simulation and numerical simulation, due to the high acceptance of these two methodologies. Physical simulation is regarded as a thermal–mechanical solution conducted by the Gleeble 3500 simulator and which can distribute the heat-affected zone (HAZ) of the obtained weld joint into four typical HAZs. These are coarse-grained HAZ, fine-grained HAZ, inter-critical HAZ and sub-critical HAZ. A combination of ferrite and tempered martensite leads to the softening behaviour at the sub-critical HAZ of DP590, which is verified to be the weakest area, and influences the final performance due to ~9% reduction of hardness and tensile strength. The numerical simulation, relying on finite element method (FEM) analysis, can distinguish the temperature distribution, which helps us to understand the relationship between the temperature distribution and real microstructure/performance. Based on this study, the combination of physical and numerical simulations can be used to optimise the flash butt welding parameters (flash and butt processes) from the points of temperature distribution (varied areas), microstructure and performance, which are guidelines for the investigation of flash butt welding for innovative materials.
  • Thumbnail Image
    ItemOpen Access
    Strain hardening and strengthening mechanism of laser melting deposition (LMD) additively manufactured FeCoCrNiAl0.5 high-entropy alloy
    (Elsevier, 2022-10-05) Zhu, Lisong; Geng, Keping; Wang, Jun; Sun, Da; Shan, Mengdie; Lu, Yao; Zhang, Xuesong; Cai, Yangchuan; Han, Jian; Jiang, Zhengyi
    In order to develop the high-entropy alloy (HEA) with low cost and excellent mechanical properties for structural applications, the FeCoCrNiAl0.5 HEA has been fabricated by laser melting deposition, one of the advanced additive manufacturing methods. Strain hardening behaviour has been analysed and discussed using the combination of characterisation techniques. The LMD-ed FeCoCrNiAl0.5 had a true yield strength and strain of ∼463 MPa and 2.94%. Also, the true tensile strength of the LMD-ed FeCoCrNiAl0.5 reached 876 MPa, together with the ductility of 24.97% (engineering strain). The LMD-ed FeCoCrNiAl0.5 HEA exhibited a dual-phase structure of 93% face-centred cubic (FCC) phase and 6.9% ordered B2 phase. The phase boundary between the disordered FCC and ordered B2 phases played a key role in the barrier, which can block the movement of dislocations because of the lattice distortion, very large angle, and mismatch of the lattice. Dislocation pile-up and tangle caused the dislocation density near the phase boundaries to be higher than that in other areas, meanwhile, they further prevented the movement of dislocation under stress as they generated back stress, therefore LMD-ed FeCoCrNiAl0.5 HEA had a good strain hardening behaviour with a strain hardening exponent of 0.92. This study provided an innovative insight into the development of HEAs with ordered phase by laser additive manufacturing for structural applications.